Please be aware we use cookies to make your experience better. A cookie is a piece of data stored on a visitor's hard drive to help us improve your access and identify repeat visitors. Cookies can also enable us to track and target the interests of our users to enhance the experience on our site. Usage of a cookie is in no way linked to any personally identifiable non-public information. Learn more.
TXM24Q-1EG
- Buy 5 for $1,067.00 each and save 3%
The TXM24Q-1EG integrated StepSERVO™ is a drive+motor unit, fusing a NEMA 24 step motor and a servo drive into a single device. Power to the drive, located at the rear of the motor, must be supplied by an external DC supply. StepSERVO technology combines the high torque capabilities of a step motor with the closed loop dynamic control of a servo system. The result is a highly customizable all-in-one motion control solution that operates quietly and efficiently, requiring only the minimum amount of current to maintain commanded position and velocity. Boost torque of 25-50% higher than the rated holding torque that is available from this integrated StepSERVO motor increases the limits of acceleration, leading to faster cycle times. With software selectable servo loops that have been pre-tuned for various inertial loads, the TXM StepSERVO can be applied in systems where a traditional stepper would not be capable of achieving the high accuracy required.
The TXM24Q-1EG integrated StepSERVO motor features Q programmability for stand-alone operation as well as streaming command capability for dynamic system configuration and host communication. All drive+motor features can be accessed over Ethernet, including more than 100 commands and 130 registers for controlling motion, I/O, configuration, polling, math, register manipulation, and Q programming. This integrated StepSERVO can be operated in several different control modes, including Streaming Command mode using either SCL, Pulse & Direction mode, and Velocity mode, plus it has the ability to run a Q program stored in non-volatile memory. Q programs are created using Applied Motion’s Q Programmer™ software, which provides powerful commands for motion, I/O, conditional processing, multi-tasking, math functions, and more. All TXM24 units are setup, configured and tuned using Applied Motion’s Step-Servo Quick Tuner software with built in Q Programmer.
Each TXM24 integrated StepSERVO comes with 3 digital inputs, 1 digital output, and 1 analog input. The digital inputs accept signals of 5-24 VDC and can be used for connecting pulse & direction signals, end-of-travel limit switches, jog switches, quadrature encoder signals, PLC outputs, sensors, or many other signal types. The digital output can be connected to PLC inputs, counters, lights, relays, or other devices. The analog input accepts 0-5 VDC signals and can be used for velocity and position control. The TXM24Q-1EG comes with a fast 10/100 MBit Ethernet port for programming and communications via TCP and UDP protocols for sending commands from Applied Motion’s proprietary serial command language (SCL). All TXM24 models are RoHS compliant. The TXM motors also meet IP65 standards to ensure reliable operation in wet and dusty installation environments.
Features
Manufacturer | Applied Motion Products |
---|---|
Youtube embed key | fJBpINlLFOQ |
Communication/Interface | Ethernet |
Max Holding Torque (mNm) | 819.00 |
Max Holding Torque oz (in) | 116.00 |
Max Length (mm) | 71.00 |
Max Length (in) | 2.80 |
Min Operating Temperature (°C) | 0.00 |
Min Operating Temperature (°F) | 32.00 |
Max Operating Temperature (°C) | 85.00 |
Max Operating Temperature (°F) | 185.00 |
Shaft Diameter (mm) | 10.00 |
Shaft Diameter (in) | 0.39 |
Max Input Supply Voltage (VDC) | 70.00 |
Motor Construction | Hybrid Stepper |
NEMA Frame Size | 24 |
Number of Axes | 1 |
Operating Mode | Analog Positioning, Analog Torque / Velocity, Encoder Following, Q Programming, Streaming Commands, Step & Direction, Velocity Control |
Rotor Inertia (kg-m-s²) | 2.80E-05 |
Rotor Inertia (oz-in-s²) | 3.97E-03 |
Setup | Software Setup |
Shaft Orientation | In-line,Single-nded |
Step Angle (°) | 1.8 |
Sample image only. Product may differ