PRODUCTS STEALS & DEALS TEXTBOOKS & VIDEOS TECHNICAL SUPPORT CUSTOMER SERVICE NEWS
Other Products
DMC-18x6 - PCI BUS Motion Controllers
DMC-18x6
PCI BUS Motion Controllers
Galil Motion Control Inc
From: $1,095.00/ea
Model MCH-2  - Stepper Motor Motion Checker
Model MCH-2
Stepper Motor Motion Checker
Nippon Pulse America
From: $145.00/ea
AZBE20A8 - Analog Input Trapezoidal Brushless Servo Amplifiers
AZBE20A8
Analog Input Trapezoidal Brushless Servo Amplifiers
Advanced Motion Controls
From: $280.00/ea

SWM24 Series NEMA 24 frame Integrated Motor/Drives

Integrated IP65 Stepper Motors

Torque to to 340 oz-in

SWM24 Series NEMA 24 frame Integrated Motor/Drives - Integrated IP65 Stepper Motors
from $605.00/ea

SWM integrated steppers are IP65 rated drive+motor units, fusing step motor and drive components into a single splashproof and dustproof device. This space-saving design eliminates wiring and saves on cost over conventional motor and drive solutions.

The SWM24 integrated steppers combine high torque NEMA 24 step motors with a sophisticated, 6.0 A/phase (peak-of-sine) step motor drive. Power to the drive, located at the rear of the motor, must be supplied by an external DC supply. Applied Motion offers compatible 24 and 48 volt DC power supplies for exactly this purpose.

All SWM24 integrated steppers are RoHS and CE compliant.

Control Options:

The SWM24 integrated steppers come with the choice of three control options: S, Q, and C.

  • The “S” control option means the drive can operate in the following control modes: step (pulse) & direction, velocity (oscillator), and streaming serial commands (SCL). (SWM24 integrated steppers do not support stored-program operation with the Applied Motion 4-axis and 8-axis SiNet Hubs).
  • The “Q” control option means the drive can operate in all of the same control modes as the S option, plus the ability to run a Q program stored in non-volatile memory. Q programs are created using Applied Motion’s Q Programmer™ software, which provides powerful commands for motion, I/O, conditional processing, multi-tasking, math functions, and more.
  • The “IP” control option means the drive is designed to operate on a Rockwell PLC-based EtherNet/IP communication network.

 

All SWM24 integrated steppers, whether they come with the S, Q, or IP control option, are setup and configured using Applied Motion’s ST Configurator™ software.

Encoder Option:

1000-line (4000 count/rev) incremental encoders are included in all SWM24 models. The encoder is housed inside the same enclosure as the drive electronics, providing protection from dust, liquid and debris. The addition of the encoder means the stepper can perform special functions not available otherwise. Stall Detection notifies the system as soon as the required torque is too great for the motor, which results in a loss of synchronization between the rotor and stator, also known as stalling. Stall Prevention actually prevents stalling of the step motor by dynamically adjusting motor speed to maintain synchronization of the rotor to the stator. This unique feature allows step motors to operate in a much broader range of applications than previously available to step motors, such as torque-control applications. The Stall Prevention feature also performs static position maintenance, which maintains the position of the motor shaft when at rest.

Inputs/Outputs:

The RS-232 based SWM24SF and SWM24QF model numbers come with 4 digital I/O points, called Flex I/O points, because each point can be individually defined as an input or an output. As inputs, the Flex I/O points accept signals of 5-24 VDC and can be used for connecting pulse & direction signals, end-of-travel limit switches, jog switches, quadrature encoder signals, PLC outputs, sensors, or many other signal types. When defined as digital outputs, the Flex I/O points can be connected to PLC inputs, counters, lights, relays, or other devices.

The Ethernet-based SWM24S, SWM24Q and SWM24IP models come with 3 digital inputs and 1 digital output. The digital inputs accept signals of 5-24 VDC and can be used for connecting end-of-travel limit switches, jog switches, quadrature encoder signals, PLC outputs, sensors, or many other signal types. The digital output can be connected to PLC inputs, counters, lights, relays, or other devices.

All SWM24 model numbers come with 1 analog input. The analog input accepts 0-5 VDC signals and can be used for velocity and position control.

Communication Ports:

SWM24 integrated steppers with the S and Q control options are available with either RS-232 or Ethernet ports for programming and serial communications. For single-axis applications where no serial networking is required the RS-232 option is recommended. RS-232 version also supports Modbus/RTU communication. For applications where communications over a network are required the Ethernet option is recommended.

Product Availability:
In Stock: Ships in 3-5 Days
(Expedited Airfreight Option Available For Sooner Delivery)

Features of Integrated IP65 Stepper Motors

  • Rated IP65 for wet and dusty environments
  • M12 connectors
  • Anti-resonance
  • Torque ripple smoothing
  • Microstep emulation
  • NEMA 24 frame size
  • Stored programming option for stand-alone operation
  • Step direction, velocity and streaming command control modes
  • RS-232, Ethernet and * EtherNet/IP Communication options
  • Modbus/RTU for easy communication with PLC or HMI
  • Built-in incremental encoder

Name/Description 1-4 (US$) 5-9 (US$) 10-24 (US$)
Step Direction with RS-232, encoder and Flex I/O
SWM24SF-3AE
 605.00  605.00  592.00
Q programmable with RS-232, encoder and Flex I/O
SWM24QF-3AE
 733.00  733.00  718.00
Q programmable with Ethernet, encoder 3 inputs, 1 output
SWM24Q-3EE
 754.00  754.00  738.00
EtherNet/IP, encoder, 3 inputs, 1 output
SWM24IP-3EE
 814.00  814.00  797.00
 

Select items to add to your shopping cart.

* Call for special quantity pricing.

 
There are no listed accessories for this product at this time.
 Links to Downloadable Files:
STM Series Product Presentation
Download Size: 3,363.33 kb
 External Links to Downloadable Files:
-Product Training Video
http://www.applied-motion.com/videos/stm-integrated-steppers
-User Manual
http://www.applied-motion.com/sites/default/files/hardware-manuals/SWM24%20Hardware%20Manual_920-0068B.pdf

"We are satisfied."

-Jose G., Bubble Technology

Add Your Comment  |  Read More Comments

"Dear Elizabeth Thank you very much, I am very glad to work this first time with you. You ship us at the date was..."

-J. Guajardo, VAI-INGDESI

Add Your Comment  |  Read More Comments

SERVO2GO is a Proud Sponsor of Geneva Centre for Autism